Essential Plumber Guide for Installing a Bathtub
Essential Plumber Guide for Installing a Bathtub
Blog Article
We have uncovered this great article relating to How to Install a Bathtub down the page on the internet and reckoned it made sense to discuss it with you on this site.
Mounting a bath tub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately difficult task. If the old bathtub is easily available, the job can relocate easily; if you have to open a wall to eliminate the old bathtub as well as place the brand-new bath tub, the job is much harder. In either situation, the task is within a residence handyman's abilities, although you will need a helper to move out the old bathtub and also embeded in the brand-new one. Ensure you have qualified on your own for the work and are comfortable attempting it. As opposed to working with a service provider to take over a halfway-completed project, it is much better to take into consideration using one prior to you start. Possibilities are you may require a specialist plumber to make tube links.
This post will aid you set up a brand-new bath tub in your shower room if you have actually already gotten a brand-new bathtub and don't require to transform the arrangement of your previous water pipes.
Your tools and material list ought to consist of the following:
Getting ready for the Setup
To start with, the sustaining framework supplied with the bath should be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps system to stop strain on the tub.
Fit the versatile faucet adapters to the bottom of both faucets using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its final placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, then the first thing you should do is detach the water supply. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the restricted access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipes. Once the supply pipes have been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from turning during this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old sealing compound.
Before going on to fit the brand-new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Utilizing the two wood boards under its feet, place the tub in the called for placement. The wood boards are valuable in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following goal is to guarantee that the tub is leveled all round. This can be achieved by checking the level and also changing the feet on the bathtub till the spirit level checks out level.
To set up faucets, fit all-time low of the outermost flexible faucet port to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water supply and inspect all joints as well as brand-new pipework for leaks and tighten them if essential. Fill the bath tub as well as likewise examine the overflow outlet and also the regular outlet for leakages.
Lastly, take care of the bathroom paneling as described in the producer's instruction manual. Tiling and also sealing around the tub ought to wait till the bath tub has been made use of a minimum of when as this will resolve it right into its last placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin ensuring that the washing machines remain in place between the faucet as well as the sink. Secure the faucet in position with the manufacturer offered backnut. As soon as the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to split a stiff seal, causing the water to penetrate the wall between the bathroom and the tiling, bring about complications with dampness as well as feasible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your fixtures and also fittings. They are sold in tubes and cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly fill the bath tub with water before sealing, to allow for the motion experienced when the tub remains in use. The sealer can break fairly very early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the marketplace. It is suggested to fit the ceramic tiles using water-resistant or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I was thinking sharing that chunk was worth the trouble. Enjoyed reading our blog posting? Please share it. Help someone else check it out. I value reading our article about Tools You Need to Install a New Bathtub .
Get Quote Report this page